M4 screws — what they fit

the VESA standard specifies M4 for these patterns

10-12mm typical · confirmed

VESA 100x100 rear pattern, M4 hardware included

8-10mm · reported

VESA 100x100, M4 screws

8-10mm · reported

VESA 100x100, M4 hardware

8-10mm · reported

Samsung documents M4 as one of three sizes (M4/M6/M8) by model

8-12mm · confirmed

VESA 75x75 and 100x100 M4 threads

8-10mm · reported

VESA 75x75 M4 inserts in a thin chassis

6-8mm · reported

ship with M4x10/12/15/20 sets for 75/100 VESA

10-20mm · confirmed

VESA 100x100 mount holding a mini-PC behind the display

8-10mm plus standoffs · reported

M4 into the VESA pattern (smaller screws hold the Pi itself)

8-10mm · reported

M4 machine screws at bracket attachment points

6-10mm · reported

drive bay and expansion slot thumbscrews (US cases often 6-32 instead)

5-8mm · reported

hinge plates and drawer slides

8-16mm · reported

small VESA 75 adapters for tablet stands

6-10mm · reported

panel and bracket screws

8-20mm · reported

chassis lids and PCB standoffs

6-12mm · reported

arm-to-frame bolts on larger hobby quads (motors are usually M3)

8-16mm · reported

secures the camera plate onto the gimbal handle arm

10-25mm · reported

clamps the scope ring halves around the tube

10-16mm · reported

cymbal stand and hardware joints

10-20mm · reported

the latch and port hardware that keeps the seal tight

6-15mm · reported

small trim panels around the console and vents

8-14mm · reported

holds the control panel and display to the cabinet

8-14mm · reported

the lid panel you remove for service access

10-16mm · reported

top control console and button panel

8-12mm · reported

handle bracket to the fridge or freezer door

10-16mm · reported

the bottom vent grille over the condenser

10-14mm · reported

outer case and controls on a countertop microwave

8-14mm · reported

holds the cyclone and motor bucket together

10-20mm · reported

holds the outer plastic panels together

10-16mm · reported

secures the group head to the boiler or brew unit

10-20mm · reported

the case around the cells

12-20mm · reported

the retractable lower guard

12-18mm · reported

the cam dowel that draws two panels together

25-35mm · reported

attaches the cabinet hinge plate to the cabinet side

10-16mm · reported

secures ball-bearing runners to the cabinet

10-16mm · reported

strike plate and hinge leaves on European frames

16-25mm · reported

attaches the hotend assembly to the carriage

10-20mm · confirmed

holds the bed to the Z carriage over springs

20-35mm · confirmed

mounts shelves and trays to the rails

10-12mm · reported

secures a power distribution unit to the rack frame

10-16mm · reported

fixes a DIN clip or bracket to the equipment

8-12mm · reported

secures a woofer or tweeter flange into the cabinet

12-20mm · reported

Attaches the stand base to the TV chassis

14mm · reported

Shorter stand screws on small TVs

10mm · reported

Mount ball joint locked by an M4 grub screw; the 1/4"-20 is the separate camera thread

6-8mm · confirmed

Replacement rail-mount screws sold in metric M4 Torx, 10mm thread length

10mm · confirmed

End caps and surface clips for LED extrusion channels

6-12mm · reported

Doorbell kits mix small metric security screws with imperial wall screws

6-25mm · reported

Rear badges and emblem posts

6-10mm · reported

Plastic bodywork fastened with well nuts

10-20mm · reported

Chartplotter and fishfinder case screws, stainless

8-12mm · reported

Cabinet hinges and latches

8-16mm · reported

Cover and choke lever screws

10-16mm · reported

Baitcaster and spinning reel side plate screws

6-10mm · reported

Wall plate mounting for thermostats and controls

20-25mm · reported

Vent faceplate screws

10-20mm · reported

Fixture cover plate screws, stainless

10-16mm · reported

Interior electronics module mounting screws

6-12mm · reported

Trim ring and driver mounting

8-16mm · reported

Pro audio cabinet grilles and handles

10-20mm · reported

Marco Specialties part listed as M4-0.7 x 8 coarse thread

8mm · confirmed

Metric equivalents used when rebuilding US machines with metric stock

8-25mm · reported

Alignment pyramid adapters use socket screws for adjustment

10-20mm · reported

Buckle and clip screws on chest straps

5-10mm · reported

Motor bracket and belt tension bolts

10-20mm · reported

Shackle retainer and lock body screws

6-12mm · reported

Faceplate and strike screws in metric door hardware

10-20mm · reported

Carriage and frame bracket screws

6-14mm · reported

Self-tapping screws holding the rear panel

10-16mm · reported

M4 x 12mm with flat washers is the usual small-VESA spec

10-12mm · reported

Most monitors under 27in mount with M4

8-12mm · reported

M4 hex screws for larger scale chassis parts

assorted · confirmed

M4 screw plus locknut for GoPro tab mounts

15-20mm · confirmed

Base plate mounting screws, M4-M5 class

varies · reported

UK-standard terminal blocks offered in M3 and M4 terminal versions

n/a · confirmed

Bracket and pole clamp hardware for the sensor suite

varies · reported

Standard rail adapter mounting hardware

n/a · reported

MIS-D flat panel mounting interface uses M4 screws

8-10mm · confirmed

Mini PC VESA plates use M4 matching MIS-D

8-10mm · reported

M4/M5 corner brackets on 2020-class printer frames

8-16mm · reported

M4 cage nuts for patch panels and lighter gear

8-12mm · confirmed

Connector and panel fixing screws on rack cards

6-12mm · reported

Brass DIN rail terminal blocks with M4 screw terminals

n/a · confirmed

Thicker radiators from some brands use M4 instead of M3

20-30mm · confirmed

Official DJI RS Screw Kit includes four M4 x 10mm screws for axis-arm and accessory mounting (camera plate itself is 1/4-20)

10mm · confirmed

Plate carries both 1/4-20 and M4 threads for baseplate accessories

6-10mm · reported

Finder shoe with 14mm hole spacing sized for M4 screws into the telescope tube

6-12mm · confirmed

M4 x 0.7 x 12mm stainless round-tip set screw per ScopeStuff size database

12mm · reported

M4 x 6mm painted instrument panel screw for the LXNAV V8

6mm · confirmed

M4 x 12mm painted instrument screw for all Winter mechanical instruments

12mm · confirmed

Listed as an M4 screw in Diebold Opteva cassette/module spare-part catalogues

5-20mm · reported

M4 x 5mm cross flat-head self-tapping screw in the NCR S2 dispenser module

5mm · reported

M4 slotted nylon screw, ~5-6mm, listed as a DN100 ATM spare

5-6mm · reported

Sixteen M4 x 8mm flat-head Phillips screws attach rack flanges to a PXI instrumentation chassis

8mm · confirmed

CCS Type 1 DC charging connector repair kit specified with M4 x 20 screw hardware

20mm · confirmed

0.70mm pitch, head 6.78-7.22mm, 3mm hex key

5-40mm · confirmed

Head 7.5mm diameter, 2.2mm high

5-40mm · confirmed

MIS-D (75x75 and 100x100mm) monitor mounting holes are M4 threaded per the VESA FDMI standard

8-12mm · confirmed

MIS-E pattern (200x100mm class) also uses M4 threaded inserts per FDMI

8-12mm · reported

4mm2 DIN-rail terminal block with M4 screw-clamp connection

clamp screw · confirmed

Camera base attaches to the adaptor plate with three M4 x 15mm screws per the installation guide

15mm · confirmed

Solar panel frame grounding holes (~4mm) are typically fitted with M4 grounding bolts and lugs

8-12mm · reported

M4 x 8mm thumb screw for the coin mech holder latch

8mm · confirmed

M4 x 27mm pan-head screw with nut for validator assembly front plates

27mm · reported

M4 x 16mm cylinder-head screw, part 5017690, used across the vending range

16mm · reported

VESA plate installed with 4x M4 screws plus nylon/rubber washers

not stated · confirmed

M4 x 12 socket-head cap screws with M4 nuts and split lock washers to rack the instrument

12mm · confirmed

Sensor bracket for tie-rod pneumatic cylinders, M4 interface, 0.6-1 Nm

not stated · confirmed

M4 screws M4x5 through M4x25 listed in the official Prusa cheatsheet

5-25mm · confirmed

secures Alpha Series display to mast bracket (hex socket drive screws)

14mm · confirmed

secures flat washers for display mounting

9mm · confirmed

secondary mirror collimation screws on Schmidt-Cassegrain optical tubes

8-10mm · confirmed

post mounting tapped hole option (8-32 or M4)

n/a (tapped hole) · confirmed

tapping screw securing cups-heater pipe/grid assembly

13mm · confirmed

TCEI (socket head) screw securing right lateral panel

12mm · confirmed

set screw (M4x6 C) on arm shaft balance

6mm · confirmed

set screw on thread take-up lever supporter shaft

8mm · confirmed

set screw on arm shaft balance pin

6mm · confirmed

optic retaining screws, tightened with 4mm hex key

n/a · reported

installation hardware referenced in official user manual (mounting/assembly)

n/a · reported

Terminal connection screws inside the electrical termination block

N/A · confirmed

Flat-head M4x6 and pan-head M4x5 screws securing EMV cover plate/base plate on POS self-service stand

6mm · confirmed

VESA mount holes, x4, min screw depth 8mm from mount surface, max screw length 9.9mm

9.9mm · confirmed

VESA mount threads, x8, max thread engagement depth 6mm

6mm · confirmed

75x75mm VESA mount, M4 threads x4, max thread depth 5mm, hand-tighten only (max 12.4 in-lb)

5mm · confirmed

M4x10 screws (qty 4, item C) for attaching adapter bracket to smaller TVs/displays per VESA hole pattern

10mm · confirmed

M4 countersunk screws securing the second (inner) door of the enclosure

N/A · confirmed

4x M4x16mm mounting screws with M4 hex nuts used to mount the enclosure into a rack via M4 screw slots

16mm · confirmed

M4 x 22mm pan-head machine screws (x2) securing the interior mounting plate/lock body to the door

22mm · confirmed

VESA mounting plate for gang-box mounted digital signage player

N/A · reported

Elo Common Peripheral Mount and Edge Connect accessory mount screws on I-series kiosk enclosures

N/A · confirmed

M4 screws used for adjustable rack-ear and panel mounting hardware inside 1U fiber enclosure

N/A · reported

M4 screws for rack mounting ears and cassette securing hardware in 4U fiber enclosure

N/A · reported

M4 mounting screws for cassette/module retention within 1U multi-function fiber enclosure

N/A · reported

Screw fastens cable cover/plug lock at rear of payment terminal (2x screws referenced in drawing)

N/A · reported

Ring and interface clamping screws

n/a · confirmed

Drive dog grub screw, stainless with threadlock

3mm · confirmed

Scope base torque spec listed alongside legacy 6-48/8-40 imperial fasteners on some product lines (note: most Weaver hardware is imperial UNC)

n/a · reported

Operator's manual torque table specifies "M4X0.7-12.5MM" for "SIG PRO CUT SLIDES, SIG P365 SLIDES WITH M4" and "M4X0.7-12MM" for other listed mounting surfaces

12-12.5mm · confirmed

Fastener manufacturer engineering drawing for a screw explicitly dimensions the thread as "M4X0.7", used on an optics-mount tapped-hole assembly with a nylon-tipped set screw "for securing of mounted optic"

not specified beyond drawing dims · reported

Installation guide bill of materials lists "4 M4 x 20 FHMS" flat-head machine screws as part of the scanner adapter mounting hardware kit

20mm · confirmed

Spec document defines an 'M4 threaded stylus range' optimized for stiffness/weight on high-accuracy TP7M probes

varies by stylus model · confirmed

Official parts list explicitly specifies 'Screw M4*25mm', 'Screw M4*14mm', and 'Screw M4*8mm' for chassis/wheel/motor assembly

8-25mm · confirmed

Manufacturer catalog entry explicitly lists 'CAP SCREW ROUND HEAD HEX M4' as a Makeblock platform component

varies (listed ~22-30mm below head) · confirmed

Aftermarket metal Technic-compatible axle explicitly sold as '45L THREADED M5 Metal Axle' -- note this specific listing is M5, included here for cross-reference to the M4/M5 family used in metal Technic-style axle replacements

45L (Technic stud length), threaded full length · confirmed

Replacement screw set lists 4x M4x16mm socket cap screws and 2x M4x8mm screws used to assemble the matte box

M4x16mm, M4x8mm · confirmed

Same listing confirms M4 as one of the included thread sizes for camera cage/rig hardware

assorted lengths in kit · confirmed

"Screw, Metric M4 X 8" (part RPH130), a Phillips pan head machine screw sold as a replacement part for Tuttnauer manual autoclaves

8mm · confirmed

GCX mounting guide: "Attach the VESA Plate to the Aestiva 7900 Ventilator using the M4 x 16mm pan head machine screws (4) provided"

16mm · confirmed

Installation guide: "attach VESA PLATE to MONITOR using 4x M4 SCREWS"; accessory kit lists "4 x M4 10mm screws, 4 x M4 14mm screws"

10mm / 14mm · confirmed

Jukebox parts retailer lists a 'PCB post 20 mm M4 thread' standoff used as general jukebox hardware, alongside separate imperial (UNC) hardware categories for other jukebox fasteners.

20mm post length · confirmed

KONE parts catalog page for part DEE0056647 lists 'HEX CAP SCREW,M4X20MM DIN933 8.8 A2B', with component family codes covering Escalator Drive station, Escalator Chain guide, Escalator Contact mat, and Escalator Illumination.

20mm · confirmed

Konsew parts listing explicitly titled 'Genuine needle plate screw M4 Juki' (Product Code SM2040750TP), a Juki OEM replacement screw that secures the needle plate on Juki industrial sewing machines

not specified · confirmed

Bopla product page titled 'M4x7' under Cable glands / General Accessories > Earthing screws, an M4x7 earthing screw used with Bopla enclosure cable-gland accessories

M4x7 · confirmed

Datasheet states: 'Lid is secured with included M4 stainless steel machine screws which are threaded into corrosion resistant bushings for repetitive...' use, for the Type 4/4X, 6/6P enclosure line

not specified · confirmed

Multiple tripod-adapter product listings explicitly sell '1/4-20 female to M4 male' thread adapters, confirming M4 threads are used on some camera/webcam and mic-stand mount hardware as an alternative to 1/4-20.

Standard adapter length · confirmed

Anderson's Bicycle Company listing gives option 'Size: M4 x 9mm' for Trek Speed Concept stem faceplate bolt (alongside an M5x18mm option)

9mm · confirmed

Elanus Parts sells 'M3x10' and 'M4x10 Flat Head Derailleur Hanger Screw' explicitly labeled by metric size for hanger/frame attachment

10mm, 12mm · confirmed

ShunTool guide states 'Shimano derailleur limit screws are typically M4 size ... DA screws are M4 x 11.5 for the rear RD and M4 x 10 for the FD. The B screw is M4 x 12'

10mm, 11.5mm, 12mm · reported

Bogensportshop sells a 'BSS Set Screw M4 x 8 mm Stainless Steel' listed under archery components/screws-nuts category, though not tied to a specific named sight product

8mm · reported

Genuine Samsung refrigerator tapping/machine screws explicitly specified as M4 (e.g. part 6002-001122 'FH 1 M4 L14', part 6002-000520 'Screw, Phillips, Self Tapping, TH, +, M4, L12', part 6001-000595 'Screw-Machine;Ph,+,No,M4')

L10-L14mm (self-tapping and machine variants) · confirmed

OEM dishwasher screws explicitly listed as M4: 'Samsung 6003-001284 Dishwasher Phillips Head Tap Screw, M4', 'Screw-Tapping;Th,+,2,M4,L12,Pass,Sts304' (6002-001435), and GE WD02X22319 'Dishwasher Screw M4'

L12mm (tapping) · confirmed

OEM oven/range screws explicitly labeled M4: 'Screw-Tapping;Th,+,2S,M4,L10' (6002-000558, range), 'Screw-Tapping;Fh,+,2S,M4' (6002-001316, wall oven), 'Screw-Machine;Th,+,M4,L10' (6001-003234, wall oven)

L10-L20mm · confirmed

Kit contents list part 009-0006593, 'Screws M4 x 10 (2 pcs)' for scale controller assembly

10mm · confirmed

8 x M4x10 bolts used to secure bearings in the Z-stage assembly

10mm · confirmed

Assembly instructions call out M4x16 (SHC), M4x6 (SHC) alignment screws, and an M4 grease fitting threaded into the linear bearing block

16 and 6mm · confirmed

M4x6mm Button Head Screws (drag chain hardware) and M4x30mm BHCS used to attach the grounding block

6 and 30mm · confirmed

Screw kit for 1-arm support, Bosch Smart System e-bike motor/display mount

12mm · confirmed

8-piece pan head self-tapping screw kit for Furrion trim kit parts (RV appliance installation), part #C-FMSN09A-008

10mm · confirmed

Wiring/control terminal screws, tightening torque 1.6 Nm per torque table

· confirmed

Catalog lists 'BFSC M4X9T' and 'BFSC M4X30' screw variants for busbar/enclosure rail mounting

9mm · confirmed

Install the WBA into the host machine using Round Head M4 mounting screws (3 mounting holes per side)

· high

M4 x 24 mm screw option for attaching projector to mounting plate

24mm · high

Pan head screw, item 001 in official parts drawing (housing screw)

22mm · high

Pan head screw, item 002 in official parts drawing (housing screw)

35mm · high

Pan head screw listed in official parts breakdown

6mm · high

Pan head screw, multiple occurrences in official parts breakdown

8mm · high

Pan head screw with washer/grip (WITH WG), multiple occurrences

7mm · high

DJI RS Screw Kit (official DJI Store part) includes four M4 screws, 10mm long, plus 1/4"-20 D-ring camera screws

10mm · confirmed

ScopeStuff customer-compiled screw-size database lists 'Celestron NexStar 8 eyepiece holder = M4-.7 X 12mm SS round tip'

12mm · confirmed

ScopeStuff database: 'Meade 2" to 1-25" adapter (1) = M4-.7' and 'Meade 1.25" visual back (where the prism goes in) (1) = M4-.7'

· confirmed

ScopeStuff database: 'Discovery DHQ 8" dob 1.25" rack and pinion focuser eyepiece screw (2) = M4'

· confirmed

ScopeStuff database: 'Main Barrel, eyepiece extension tube holder (2) = M4-.7'

· confirmed

Retailer product listing explicitly titled 'SkyWatcher-style Shoe for Finderscope Bracket with 2 Holes - BLACK - M4 Screws', confirming M4 mounting screws for the finder shoe

· confirmed

UK parts retailer product titled 'Genuine needle plate screw M4 Juki'

· medium

Product listing explicitly gives dimension 'M4 x 6mm' for the needle plate screw

6mm · high

Rack bracket screw B, secures bracket to rack

10 · confirmed

Bracket-to-rack screw, 8pcs included in package

10 · confirmed

M4 tap for cage rod mounting

not stated · confirmed

M4 tap, total length 41mm

41 · confirmed

M4 tap for cage rod attachment

not stated · confirmed

M4 tap

not stated · confirmed

M4 tapped hole in one end

101.6 · confirmed

Manual states the grounding terminal connection is 'secured using an M4 x 6mm screw, a plain washer and a star/lock washer' torqued to 10 N·m; spares list also includes an 'Xgard Bright Spare M4 x 8 Posi Pan Head Screw' and 'Spare/Replacement M4 Earth Stud Assembly' plus M4 threaded hex spacers (10mm and 15mm)

6-15mm · confirmed

OEM replacement part explicitly named 'SCREW M4X8; DIN 84A 4.8 ZINC PLATED', part #SP309084000408

8mm · confirmed

OEM replacement part explicitly named 'SCREW, M4X25 DIN 933 8.8 ZINC PLATED', part #569655

25mm · confirmed

Parts manual lists 'FLAT WASHER M4×∅ 9×0.8' (part #1421409) for the recovery tank group

washer only (no screw length specified) · confirmed

'Oil cup made of brass with M3 or M4 connection thread. For screwing into steam engines, flame eaters and Stirling engines'

n/a (fitting thread) · confirmed

'M4*0.5 Thread Elbow Pipe Fitting for KACIO Steam Engine Boiler Model' — explicit M4 x 0.5 pitch pipe fitting thread

n/a (fitting thread) · confirmed

'TS-Optics Knurled M4 Screw... fits many Diagonals, Adapter and Focuser. Length of the M4 thread: 10.5 mm Length of the screw: 17.5 mm'

10.5-17.5mm · confirmed

'using 2pcs M3 non-slip brass handle screws... There is 1pc M4 brass lock screw in middle part' for a 1.25in helical focuser

n/a · confirmed

Kiosk integration manual: 'Retain the panel PC module to the Kiosk cabinet with four M4 nuts'

n/a (nuts) · confirmed

Parts list: 'ITEM 10, QTY 8, M4x16 Screw Bezel Screws'

16mm · confirmed

Service manual explicitly calls out 'Screw M4 x 8 mm' as a removal/replacement part in the disassembly procedure

8 mm · confirmed

Service manual instructs 'Remove two screws (Semus M4 x 8) and remove the inner case'

8 mm · confirmed

Rewinder media guard limiter is secured with a screw called out as M4*8L in the service manual

8 mm · confirmed

Genuine OEM spare part is an A2 stainless steel pan head Pozi machine screw explicitly specified as M4×25 mm, used in the robot's structural assembly

25 mm · confirmed

Service manual specifies maximum tightening torque of 2.2 Nm for M4 screws used in grinder reassembly

not specified · confirmed

Stainless steel screw listed in official Model 330M replacement parts catalog

8mm · confirmed

Stainless steel screw, Model 330M parts catalog

6mm · confirmed

Installation manual gives dual units: M4 x 1" (25mm)

25mm · confirmed

Manual gives M4 x 1/2" (12mm)

12mm · confirmed

Alternate metric length variant listed in the same installation manual

16mm · reported

Manual: 'lock the AC/COM cover with screws (M4x10)'

10mm · confirmed

Two M4 screws, PH2 driver, 1.6Nm torque; length not stated

not stated · reported

Spare-part listing states M4x16 hex countersunk head

16mm · reported

Hex socket cylindrical head, galvanised carbon steel, drop-resistance rated

16mm · reported

Inner hexagon cylindrical head after-sale kit M4*8

8mm · reported

Distributor kit: size M4, 2.5mm Allen key

not stated · reported

Official VESA mount guide: assemble main bracket with four M4*L10mm screws

10mm · confirmed

Tech specs list 'Screws: #10-32, M4' - both imperial and metric options supplied

not stated · confirmed

Datasheet: M4-0.7 x 20mm stainless cover screws

20mm · confirmed

Datasheet: vertical M4 thread snap-in PCB mount, screw M4 x 6mm

6mm · confirmed

Manual: thread the M4 x 20mm panhead screws through the mounting spacers

20mm · confirmed

Machine screw plus flat washer and locking nut, per installation instructions

40mm · confirmed

Bolt plus plain washer and nut, per installation instructions

40mm · confirmed

Genuine spare part YC.WJ.LL000214.01

12mm · confirmed

Rare metric exception; most rail and optic hardware is imperial #4-48/#6-40/#8-32

not stated · reported

M4 x 12 countersunk and M4 x 30 pozi pan screws

12-30mm · confirmed

Machine screws M4*8, M4*10, M4*15 in parts list

8-15mm · confirmed

M4 socket head screws are the core fastener for the 8mm-grid, 4mm-hole pattern

6-25mm · confirmed

Camera-to-bracket screws on the AM-21M mount, M4x8

8mm · confirmed

Bezel screws, M4x16, 8 required

16mm · confirmed

Handle cover screws listed as M4 x 14mm pan head Taptite

14mm · confirmed

Needle plate screw listed as M4x6, shared across many Singer models

6mm · confirmed

Genuine needle plate screw listed as M4

not stated · likely

M4 x 8mm, 20mm and 25mm tapered thumbscrews

8-25mm · confirmed

Four screw holes on the reader body for mechanical fixture, explicitly listed as M4 x 5

5mm · confirmed

Kit lists M4 x 20 flat head machine screws for base plate mounting

20mm · confirmed

Manual: fix the bracket using four allen bolts (M4, min. 5mm)

5mm minimum · confirmed

Board uses M4 standoff/mounting hole pattern to secure into printer enclosures

varies · reported

VESA FDMI standard: four M4 x 0.7 mounting screws, 6mm

6mm · confirmed

VESA FDMI standard: four M4 x 0.7 mounting screws, 8mm

8mm · confirmed

VESA FDMI standard: four M4 x 0.7 mounting screws, 10mm

10mm · confirmed

VESA FDMI standard: six M4 x 0.7 mounting screws, 10mm

10mm · confirmed

Product spec states M4 x 0.7 taps for post and breadboard mounting

tapped holes · confirmed

Bracket named for its M4 tap, mounts cage assemblies to posts

tapped · confirmed

M4 tap for 60mm cage bracket post mounting

tapped · confirmed

M4 tap for post mounting of the double-bore cage plate

tapped · confirmed

Metric variant uses M4 mounting tap where imperial uses 8-32

tapped · confirmed

Listed with M4 taps for post mounting

tapped · confirmed

M4 taps for post mounting

tapped · confirmed

Three adjusters with M4 taps

tapped · confirmed

M4 tap for 1-inch mirror flexure mount

tapped · confirmed

Product spec states M4 x 0.7 tap for post mounting

tapped · confirmed

M4 tap for 1-inch optics dual rotation mount

tapped · confirmed

SM05-threaded bore with M4 taps

tapped · confirmed

M4 tap for post mounting

tapped · confirmed

Page lists 8-32 (M4) tap for post mounting on metric variants

tapped · confirmed

M4 tap on the 30mm cage-cube-mounted beamsplitter

tapped · confirmed

M4 tap for post mounting

tapped · confirmed

M4 tap on the 16mm cage cube variant

tapped · confirmed

Metric variant listed with M4 taps for post or breadboard mounting

tapped · confirmed

Page states 8-32 (M4) taps on both ends of the metric posts

both ends tapped · confirmed

Adapters available with 8-32 (M4) tapped holes for post mounting

tapped · confirmed

Spec page lists 8-32 (M4 x 0.7) tapped holes

tapped · confirmed

Catalog data lists M4 mounting for the metric SM1-threaded variant

tapped · reported

Same catalog lists 6.0 hex M4 thread standoffs with 9.5mm thread engagement

varies · confirmed

Hardware list specifies M4 x 10 screws for the adapter bracket

10mm · confirmed

Manual states M4 Torx-20 screws for rings and optic interfaces (Aimpoint Micro, RMR, Deltapoint)

not stated · confirmed

Plate mounts via two captive M4 screws for DJI Ronin-S/SC and RS2/RSC2

captive · confirmed

M4x8 pan head

8.0mm · confirmed

Pan-head and flat-head M4X8 variants

8.0mm · confirmed

SCREW, M4X6, PAN-HEAD, CROSS-RECESS

6.0mm · confirmed

M4X18 pan-head

18.0mm · confirmed

SCREW, M4X8L, PAN-HEAD

8.0mm · confirmed

M4X6 flat-head cross-recess

6.0mm · confirmed

M4X5 pan-head cross-recess

5.0mm · confirmed

SCREW_M4X10_SPECIAL

10.0mm · confirmed

Two M4 screws on the adapter plate assembly

length not stated · confirmed

Datasheet: mounting bracket, 2x M4 screws incl. washers

length not stated · confirmed

2x M4 screws incl. washers

length not stated · confirmed

Blue panel screw M4 x 10

10mm · confirmed

Variant NT-HD-SST-M4-MT-H

length not stated · confirmed

Official Glock sheet lists M4 for this adapter group

length not stated · confirmed

M4 x 0.7 x 12mm

12mm · confirmed

M4 x 0.7 x 10.25mm

10.25mm · confirmed

Owner's manual: (2) M4 x 0.7 screws

length not stated · confirmed

SHCS M4 x 0.7 x 8.5mm per vendor writeup, not the Sig manual

8.5mm · likely

M4 x 60 machine screw listed in parts included

60mm · confirmed

M4x30 fastener in joint assembly instructions

30mm · confirmed

Service manual torque table: M4 1.5-3 Nm

length not stated · confirmed

binding post terminal stud, 32mm body

32mm · confirmed

amplifier/speaker terminal stud, 35mm body

35mm · confirmed

speaker binding post thread

· confirmed

eyepiece holder thumb screw, M4-0.7 round tip

12mm · confirmed

mounting slots take M4 (or imperial 8-32)

· confirmed

telescope accessory thumbscrews, M4-0.7

· confirmed

grade 12.9 set screw

3mm · confirmed

A2 stainless TCHC ISO 4762 door hinge/panel screw

10mm · confirmed

stainless chimney/flap box fastener PN 00-978499

16mm · confirmed

control box mounting pan head screw PN 1500647

8mm · reported

Phillips screw SC0176 with spring and flat washer

10mm · confirmed

Torx screws securing handle or MMS mount to FMS housing (x4)

8mm · confirmed

Torx screws securing FMS housing (x4)

12mm · confirmed

screws attaching Speedpoint/chassis rear hardware (x2)

30mm · confirmed

four screws attaching VESA-style bracket to display

8mm · confirmed

pan head machine screw attaching bracket to FMS

8mm · confirmed

pan head screws with NYLOC securing top/bottom housing

10mm · confirmed

button head screws for plunger case assembly, PN G6000085 (x2)

12mm · confirmed

long motor unit screw PN 020.0024 (x2)

60mm · confirmed

screw SM-6041202-TP, pitch 0.7

12mm · confirmed

set screw SM-8040412-TP

4mm · confirmed

tapping screw ST-4040851-SN

8mm · confirmed

pan head screw SM-4042501-SC, pitch 0.7

25mm · confirmed

cap head screw PN 710219 (superseded 10mm) (x4)

16mm · confirmed

Pozi head screw PN 307249 (x2)

8mm · confirmed

Torx pin countersunk screw PN 110953 (x2)

12mm · confirmed

binding head chrome screw, PN C18-1E00AAA0 (x2)

8mm · confirmed

hex socket set screw cup point black, PN C18-ZA774LLG

5mm · confirmed

screw PN 5969326.001

10mm · confirmed

DIN 7991 countersunk screw PN 5902573.001

8mm · confirmed

DIN 916 set screw PN 5904511.001

4mm · confirmed

DIN 7984 low head cap screw PN 5902572.001

16mm · confirmed

Four hex-head screws with four hex nuts secure the metal retaining brackets

40mm · confirmed

One screw secures the control unit; kit also contains imperial No.8 x 3/4in wood screws

25mm · confirmed

Two DIN 84 screws attach the DIN-rail clips

8mm · confirmed

Four VESA screws under the rear plastic cover

10mm · confirmed

Four Phillips screws supplied with the free-standing display base

10mm · confirmed

One of four VESA screw options (M4/M5/M6/M8); length depends on spacer stack

varies with spacers · confirmed

Six pan head screws (M4x22) plus two longer pan head screws (M4x35) close the housing

22mm, 35mm · confirmed

Two pan head screws in the housing/handle assembly

30mm · confirmed

Screw retaining the bushing at the nose

16mm · confirmed

Service spare part 20041461A screw

12mm · confirmed

Eight screws for initial jig assembly, 2.5mm hex key

10mm · confirmed

M4 x 4mm screws (5 supplied, 1 spare) fix mount bracket to upper case; torque 1.56 Nm

4mm · confirmed

Parts list specifies M4 nuts and M4x16 / M4x10 / M4x7 truss and hex head cabinet screws

7-16mm · confirmed

M4 pan head machine screws supplied in 6, 8, 10, 12, 16 and 20mm; needs 4 full turns of engagement

6-20mm · confirmed

M4 x 12 / 25 / 30mm display screws, 4 of each supplied

12/25/30mm · confirmed

M4 x 5, 6, 10, 12, 16 and 25mm screws including taptites and countersunk unbraco

5-25mm · confirmed

M4 x 8mm Torx countersunk screws replace the original taptites on reassembly

8mm · confirmed

Hexagon socket adjusting screw M4 x 5mm

5mm · likely

M4 tapped hole at one end of the post (M6 at the other)

n/a (tapped) · confirmed

Post kit supplied with an M4 mounting stud

not stated · confirmed

Adapter plate on the back of the VC8X is threaded for M4 screws

not stated · confirmed

M4 x 12 bolts with serrated washers, qty 4, torque about 2 Nm

12mm · confirmed

M4 threads for right/left side brackets on the camera plate

not stated · confirmed

M4 x 14mm socket head cap screws (x4) mount the Arca-Swiss plate to the lens foot

14mm · confirmed

M4 x 12mm socket head screws mount the replacement foot

12mm · confirmed

M4 x 10mm socket head screws mount the replacement foot

10mm · confirmed

M4 is the smallest size with full ESA design/torque data; LN 29949 M4 A-286 insert example

not stated · confirmed

M4 x 8, M4 x 10 and M4 x 12 stainless screws for housing, PC board and countersunk positions

8-12mm · confirmed

M4 x 30 Pozi pan screws (x2)

30mm · confirmed

Taptite bind B M4 x 12 for inner chute assembly and Taptite pan washer B M4 x 14 for the fuser unit

12-14mm · confirmed

Silver M4 x 8 machine screw, right-side mounting

8mm · confirmed

M4 x 0.7 x 12mm ground cable lug bolt, 2.5 Nm

12mm · confirmed

M4 x 0.7 hexagon socket cylinder screws (6-8 pcs) fixing the flameproof cover; M3/M4 blind threaded holes for internal component adapters

not stated · confirmed

M4 slotted set screw securing the housing cover

not stated · confirmed

Pan-head Phillips M4 x 6, 8 and 14mm chassis screws, plus star-washer M4 x 6 and washer-head M4 x 8

6-14mm · confirmed

Self-tapping Phillips M4 x 8, 10 and 12mm screws

8-12mm · confirmed

M4 x 10mm pan-head tapping chassis screw and Torx T20 M4 x 10 and M4 x 12 screw-kit items

10-12mm · confirmed

M4 x 8mm tapping screw and M4 x 12mm screw with washer

8-12mm · confirmed

Four M4 x 12mm hexalobular screws secure the control pod cover, torque 1.8 Nm, T20 or 6.4mm flat driver

12mm · confirmed

M4 screws with ring terminals at the signal shield termination points

not stated · confirmed

M4 or M5 Phillips screw with flat and star washer for the chassis grounding lug

not stated · confirmed

Four M4 screws attach the EMC clamps on the EMC mounting plate kit

not stated · confirmed

M4 screw with OT6-4 terminal for the grounding cable, torque 1.6 Nm

not stated · confirmed

Allen screw M4 x 6mm used across Heidelberg press assemblies

6mm · confirmed

DIN 933 hex head screw M4 x 5mm

5mm · confirmed

Stand assembly uses M4 x 12mm screws for guide-stand to stand and M4 x 10mm for stand to TV body

10-12mm · confirmed

Genuine LG stand screws listed as 4mm x 16mm and M4 x 20mm

16-20mm · likely

Magnet, guard and door screws supplied as M4 x 10mm sets

10mm · confirmed

Quick start guide lists M4*10 screws included for mounting the Power Hub enclosure

M4x10 · confirmed

Genuine needle plate screw explicitly sold and cataloged as M4x6mm, fitting multiple home machine models

M4x6 · confirmed

Genuine Juki needle plate screw listed explicitly as M4 thread

M4 · confirmed

Presser foot ankle screw explicitly listed as M4 x 10 stainless steel

M4x10 · confirmed

Set-screw explicitly listed as M4x12 for eyepiece fixing in eyepiece holders/focusers

M4x12 · confirmed

Crowdsourced screw-size database explicitly lists the Celestron NexStar 8 eyepiece holder thread as M4-0.7 x 12mm stainless steel round-tip

M4x12 · confirmed

Finderscope bracket shoe explicitly sold with M4 mounting screws

M4 · confirmed

Kit includes M4 x 24mm screws for mid-size projector mounting hole patterns

M4x24 · confirmed

Hardware bag includes M4 x 12mm projector adapter screws

M4x12 · confirmed

Kit specifies M4 x 10mm projector mounting screws

M4x10 · confirmed

Parts manual specifies M4 x 0.7 and M4 x 0.8 pitch fasteners for frame and motor bracket assemblies

M4x0.7 pitch, M4x0.8 pitch · confirmed

Service manual specifies M4 fasteners in multiple lengths (M4x6, M4x8, M4x10, M4x14, M4x16, M4x45) for pad/vacuum-belt applicator assembly and drive components

M4x6, M4x8, M4x10, M4x14, M4x16, M4x45 · confirmed

Assembly instructions manual for the Supreme M4 motor unit and diaphragm assembly explicitly documents M4-threaded fasteners used to secure the motor housing and caddy components

M4 (assembly fasteners, length per exploded diagram) · likely

NCR SelfServ 25/23/27 ATM Service and Parts Identification manuals list M4 machine screws for securing internal cassette guide rails and module brackets within the safe/dispenser unit

M4 (length per specific bracket, not itemized in excerpt) · likely

COSEL torque table explicitly lists M4 terminal screw diameter with torque range 1.0-1.5 N·m for higher current terminal blocks

M4x10 · confirmed

Guide explicitly states 'M4 Screw — 1.2 Nm... IEC 60999-1 Standard... used in 7.62mm pitch terminal blocks... for high-current power distribution, motor controls, and inverter outputs'

M4x10 · confirmed

Terminal Screw Torque Specifications table explicitly lists Terminal Screw Size for VFD68 drive terminal blocks including M4 with matching N·m torque values for various kW ratings

M4x8-M4x10 · confirmed

ABB's wind turbine converter hardware manual electrical-installation chapter specifies terminal/cable-lug M4 screw sizes for control and auxiliary terminal connections inside the nacelle converter cubicle

M4x10 · likely

Whirlpool factory technical service data sheet for washer control board assembly explicitly calls out M4 screws for securing the control board bracket to the cabinet in the wiring diagram/parts breakdown

M4x10 · likely

Midea Front Load Washer Technical Service Guide parts/torque section explicitly references M4 mounting screws for the control PCB assembly within the washer cabinet

M4x8 · likely

ETC Sensor+ Rack Installation Manual explicitly specifies M4 screws for module retention and terminal block mounting hardware within the dimmer rack chassis

M4x10 · likely

ETC ERn Wall-mount Enclosure Installation Manual explicitly specifies M4 mounting screws for securing the internal processing rack and terminal panel to the enclosure

M4x12 · likely

DRd Rack Enclosure Installation Manual explicitly calls for M4 screws to secure module faceplates and internal terminal hardware in the dimmer rack

M4x10 · likely

Payter Kiosk Install Manual explicitly specifies M4 screws for securing the internal reader module and electronics tray inside the kiosk housing

M4x12 · likely

EVOCHARGE EVSE Manual explicitly lists M4 screws for mounting the internal control board and terminal cover inside the EVSE enclosure

M4x10 · likely

Tommy Car Wash Controller Programming/Installation Manual explicitly specifies M4 screw terminals for input/output wiring blocks inside the tunnel controller enclosure

M4x8 · likely

Tunnel Master WBC User Manual explicitly specifies M4 fasteners for securing I/O terminal blocks and relay modules inside the control cabinet

M4x10 · likely

OPEX SureSort Operator Manual explicitly specifies M4 screws for securing electrical panel covers and control board mounts within the sorter's electrical cabinet

M4x10 · likely

7104 Series Operator Manual explicitly specifies M4 screws for control panel electronics access covers and terminal mounting on the modular inserter chassis

M4x10 · likely

IBE KL125PR Spiral Mixer Instruction Manual's block wiring diagram section explicitly specifies M4 screws for control panel terminal block and contactor mounting

M4x10 · likely

Eurodib LB Series Spiral Mixer Operation Manual explicitly calls out M4 screws for securing the electrical control box cover and internal terminal blocks

M4x12 · likely

Spiral Mixers User Manual specifications section explicitly lists M4 screws for mounting the safety guard interlock switch and control panel to the mixer frame

M4x16 · likely

Contender Planetary Mixer User Manual's electrical diagram section explicitly specifies M4 screws for the control panel terminal block and motor contactor connections

M4x10 · likely

APM-E Series II Mechanism Service Manual explicitly specifies M4 screws for securing the coin mechanism and electronics module inside the meter housing

M4x10 · likely

IPS M5 Single-Space Smart Meter datasheet/install notes explicitly specify M4 screws for securing the smart meter mechanism into existing meter housings

M4x8 · likely

NY DOT NEMA Traffic Signal Cabinet specification explicitly requires M4 screws for securing terminal and distribution assembly panels within the NEMA 3R traffic cabinet per its hardware detail section

M4x12 · likely

City of Suffolk ATC Traffic Signal Controller Cabinet standard specification explicitly calls for M4 fasteners on the load switch and terminal facility mounting panels within the cabinet

M4x10 · likely

Grindex Mega Inox IOM Manual electrical connection chapter explicitly specifies M4 terminal screws for cable lug connections inside the pump's motor terminal box

M4x10 · likely

Service manual spare-parts/exploded diagrams list explicit fastener call-outs 'M4x12, 6.8', 'M4x10, 6.8', 'M4x10' for internal chassis/weighing-cell mounting screws

M4x10, M4x12 · confirmed

6x M4x6mm button head screws hold the printed frame together

6mm · confirmed

Socket-head screws with spring and flat washers fasten the lens fixture to the bracket

10mm, 22mm · confirmed

Four M4x8mm ceiling-mount attachment screws

8mm · confirmed

Official spec: four 4mm diameter 0.7 pitch screws for 75x75 and 100x100 patterns

6mm, 8mm · confirmed

Four or six 4mm diameter 0.7 pitch screws across 200x100 to 400x400 patterns

10mm · confirmed

M4x6mm fixes the frame to the link bracket during multi-cabinet array assembly

6mm · confirmed

Headless M4 bolt on the outer cabinet edge closes inter-cabinet gaps

6mm, 8mm · confirmed

M4x12mm secures the cabinet top to the frame; M4x8mm fastens the upper cabinet left side

8mm, 12mm · confirmed

Six M4 x 0.70 pitch screws fix the rack ears

not stated · confirmed

Manual: mount engine to firewall with 4 M4 bolts, standoffs 30-50mm, 6-8mm min thread engagement

30-50 (standoffs) · confirmed

Coil mounting bracket 535-5203-03 listed with M4 thread

not stated · confirmed

Kit ships 5x M4x10 rounded-head Torx security screws for the mating-face frame

10 · confirmed

Dust screens on both sides fixed with M4 flange screws/nuts

not stated · confirmed

back cover to monitor assembly (4)

10mm · confirmed

power board mounting screws

8mm · confirmed

back cover to display assembly (4)

10mm · confirmed

VESA back cover to chassis (4)

10mm · confirmed

power board grounding screw

9mm · confirmed

DP cap / unlocking mechanism screws

11mm · confirmed

upper back cover to chassis (4)

10mm · confirmed

main/power board ground point

8mm · confirmed

stand / back cover screws 1-4

11mm (10 kgf-cm) · confirmed

stand / back cover screws 5-6

8mm · confirmed

main / power board ground screw

8mm · confirmed

back cover / main housing screws (4)

10mm · confirmed

power washer screw, ground / power board

9mm · confirmed

stand / hinge module (7)

7mm · confirmed

rear handle assembly and housing screws (9), T15 Torx pan head

14mm · confirmed

long housing / handle screw, T15 Torx pan head

30mm · confirmed

motor cover / housing screw, T20 Torx pan head

18mm · confirmed

housing screw, steel black

14mm · confirmed

arm/shoulder structural joints (~50 qty)

20mm · confirmed

vehicle/mounting-plate attachment through integrated screw holes

12mm · confirmed

PCB-to-enclosure standoff stud

5-70mm · confirmed

PCB standoff spacer

10-11mm thread length · confirmed

brass threaded insert for lid/panel mounting boss

per drawing · confirmed

enclosure grounding screw for cable glands and accessories

7mm · confirmed

DIN-rail end stop fixing flange (4.2mm hole)

not stated · confirmed

strike insert (coil unit) to lip bracket

9.5mm · confirmed

strike faceplate to lip bracket

9.5mm · confirmed

six tapped bracket base holes for turret camera pendant assembly

not stated · confirmed

Safety clip screws securing TV to bracket safety strap

12 mm · confirmed

16 mm pattern mounting screws, counterbored for socket head

varies · confirmed

post-mounting tapped holes on mount underside

not stated in datasheet · likely

mounting/optic bore tap (metric cage system)

not stated · likely

2in optic double-bore mount tap

not stated · likely

Fastening screw for the design cover (shroud).

12 mm · confirmed

Fixing screw set for the motor design cover (Part 1270016437).

53.5 mm · confirmed

Alignment plate bolts for the Removable Integrated Battery assembly.

6 mm · confirmed

Screw for securing the plexiglass to the headlight fairing.

Not specified · confirmed

Cabinet hinge latch plate screw (Part 7243291619).

12 mm · confirmed

Cheese-head screw for handpiece assembly

45 mm · confirmed

Pan head screw (3P) for doctor unit base mount installation

20 mm · confirmed

Screws for door latch repair kit and cover fixation (T25 Torx head specified in kit)

Not specified · confirmed

Setting-plate mounting screws, torque 1.1±0.1 N·m

per install surface · confirmed

VESA flat display mounting interface for small/medium displays

8-10 mm typical · high

4x M4 screws attach the plate to the lens foot

14mm · confirmed

M4x8 secures the LPL adapter; M4x12.5 mounts it to the camera cage

8mm and 12.5mm · confirmed

2x M4 screws remove the sleeve from the mechanical stage

not stated · confirmed

M4x20 grounding/terminal hardware in the terminal box

20mm · confirmed

M4 AC and control terminal bolts, torque 1 Nm

not stated · confirmed

supplied with 3x M4x10 Allen screws (part 2045400)

10mm · confirmed

M4 clamping screw option on the larger blocks in the range

not stated · reported

back cover screws (4x) and system board mounting screw (M4x8)

8 and 10mm · confirmed

mount-to-firearm fixing screw, torque 2 Nm

- · confirmed

spindle-to-carriage mount screws (3x socket head cap)

10mm · confirmed

housing mounting screws — max insertion 8mm rear, 3mm near lens, 4.5mm near connectors

3–8mm depending on hole · confirmed

needle plate screw

6mm · confirmed

genuine needle plate screw

- · confirmed

B-tension adjusting screw

13.5mm · confirmed

stroke (high/low limit) adjusting screws

11.5mm · confirmed

standard nut-and-bolt system thread for modern Meccano

5, 6, 8, 10, 12 and 25mm · confirmed

knurled locking thumbscrew clamping the eyepiece

12mm · confirmed

Focuser is fixed to the telescope tube with four countersunk screws explicitly specified as M4

not specified (user-sourced, DIY store) · confirmed

Official Maytronics/Dolphin replacement part explicitly listed as 'M4x14 - 7985-Mtil' screw for Dolphin robotic pool cleaners

14mm · confirmed

Retailer-confirmed replacement mounting-plate screws explicitly sized M4 x 5mm for securing Sanwa/Hori joystick mounting plates to arcade stick cases

5mm · confirmed

Parts list item 3: Screw, M4 by 10, part XA9-1189-000CN

10mm · confirmed

Official service manual Screw Torque List (Chapter 3) specifies Taptite Bind B M4x12 screws for T1 tray cover, side cover L, and side cover R assembly with tightening torque 0.8±0.1 N·m

12mm · confirmed

Official service manual Screw Torque List specifies Taptite Bind B M4x12 screws for T1 tray cover, side cover L, side cover R ASSY, and main shield cover plate, torque 0.8±0.1 N·m

12mm · confirmed

Manufacturer's recommended screw torque table explicitly lists 'M4 Screw Torque - 2Nm' alongside M3 for the mount's fixing screws

not specified · confirmed

DJI RS Screw Kit lists four M4 x 10 mm screws for mounting a camera to the gimbal cradle

10mm · confirmed

Dovetail mounting base uses two M4 screws for red dot / optical finderscope attachment

not specified · confirmed

Manual: chassis ground terminal takes a ring terminal suitable for an M4 screw.

not specified · confirmed

Datasheet: kit comprises 4 screws and nuts, metric thread M4 x 70 mm.

70 · confirmed

Manual: 2 x M4 fastening screws plus an M4 cable lug for functional earth on non-conductive substrate.

not specified · confirmed

Vortex compatibility chart lists the mounting fastener thread as M4 x 0.7.

not specified · confirmed

M4 tapped hole in one end (M6 in the other), 50.8 mm post.

tapped hole · confirmed

M4 tapped hole one end, M6 the other; 101.6 mm post.

tapped hole · confirmed

M4 tapped hole on one end, M2 on the other; 38.1 mm post.

tapped hole · confirmed

M4 mounting thread, for 50.8 mm optics.

tapped hole · confirmed

4° fixed angle optical mount adapter with M4 mounting threads.

tapped hole · confirmed

M4 tap for Ø2" double-bore optic mount cage plate.

tapped hole · confirmed

Front gear-case fasteners, listed as "M4 x 22mm Pan Hd. ST T-20 Screw (4)" (Torx T20, thread-forming)

22 mm · confirmed

Housing and gearcase fastening, "M4 x 18mm Pan Hd." screws

18 mm · confirmed

Hammer-case bolts, parts list "HEX. SOCKET HEAD BOLT M4X25" x4

25 mm · confirmed

Flat-head M4 screws in the rail kit (kit lists M3 flat x2, M3 pan x4, M4 flat x2, M5 x10)

unspecified · confirmed

Case joiner / middle rail hardware — four M4 bolts, 8-10 mm recommended

8-10 mm · confirmed

Stroke/reach adjust screw, "Stroke Adjust Screw (M4 x 12) & Plate"

12 mm · confirmed

Official safety screws accessory listed as "Safety screws M4 x 14" (part 5333570)

14 mm · confirmed

Mounting kit contains an L-bracket plus two M4 screws with washers

unspecified · confirmed

"PVA sensors mount to the brackets using the M4 hardware supplied with the sensors"

unspecified · confirmed

Bracket ships with "4 x fixing screws M4 x 25 for sensor WTS10"

25 mm · confirmed

Wall/cabinet mounting with four M4 screws, 6 mm long

6 mm · confirmed

Aluminium frame mounting with two wedge nuts and M4 screws

unspecified · confirmed

Instrument mounting hardware: "SCREW, M4 X 0.7 X 12 PAN HEAD, TORX T15"

12 mm · confirmed

Service manual: M4 grounding screw and M4 stop screw in the headrest, two M4 screws holding the housing to the seat housing, two M4 on the front seat housing and two on the lower parallelogram housing

unspecified · confirmed

Unit ground (PE) terminal uses one M4 x 10 mm screw; receptacle assembly uses M4 x 12

10 mm and 12 mm · confirmed

Chassis screws listed as "Screw M4 x 8 mm 0515-0910"

8 mm · confirmed

Spray chamber latch "Screw, M4 x 0.7 PH"; parts list also carries "Screw, M4 x 16"

16 mm · confirmed

Device secures to the mounting surface with the included M4 machine screws; in fibreglass or composite dash you drill and tap M4 holes

unspecified · confirmed

Kit contents: 8x M4x8 pan Torx screws and M4 Nyloc nuts

8 mm · confirmed

Rack ear kit ships with M4 screws for 1U mounting

not specified · confirmed

Manual: remove the four M4 screws and the sleeve from the mechanical stage

not specified · confirmed

ConFlat UHV reducing flange with M4 x 0.7 tapped holes

not specified · confirmed

Stud set: seven M4 x 25 mm silver-plated stainless socket screws

25 mm · confirmed

Cup ferrule column nut for Thermo Finnigan GC inlets uses M4 nut thread

not applicable · confirmed

Standard Hitachi stubs use an M4 threaded hole in the stub base

not specified · confirmed

Manual lists M4 Tx20 screws for rings, interfaces and tensioning

not specified · confirmed

Slide has two tapped hole pairs: 6-32 and M4 x 0.7 for red dot mounting

not specified · confirmed

OEM tapping screw described as truss head M4 x L12, stainless 304

12 mm · confirmed

OEM special flat-head Torx screw M4 x L43, stainless 304

43 mm · confirmed

OEM fixing screw listed as M4 x 12

12 mm · confirmed

OEM screw part 00188670 listed as M4 x 17 mm

17 mm · confirmed

Manifold fixing Torx screw M4 x 16 (C00054790)

16 mm · confirmed

Flat head tapping screw M4 x L16, stainless 304

16 mm · confirmed

Truss head tapping screw M4 x L14, zinc plated

14 mm · confirmed

OEM screw part 602608 listed as M4 x 6

6 mm · confirmed

Hexagon screw M4 x 30 mm, OEM part MM102005

30 mm · confirmed

Install guide screw B: M4 x 10 mm to fix the KVM into the rack

10 mm · confirmed

pan-head screw for base plate

6mm · confirmed

pan-head cross-recess frame assembly screws

8mm · confirmed

VESA 100x100 threads, max thread depth 7mm

depth 7mm max · confirmed

screws attaching direct mount bracket to projector

12mm · confirmed

large screws securing frame under counter

12mm · confirmed

T-slot bar / monitor bracket mounting screws

8mm · confirmed

T-slot bar assembly mounting screws

8mm · confirmed

AC terminal block screws, torque 5.6 Nm

not stated · confirmed

protective earth (PE) ground connection screws

not stated · confirmed

4 screws fixing EMC clamps

not stated · confirmed

cover plate hexagon bolts, torque 2 Nm

12mm · confirmed

surface mounting fasteners (M4 or #8)

not stated · confirmed

internal plate fastening screws

12mm · confirmed

battery module to base/PDU screws, PH2, torque 2 Nm

14mm · confirmed

housing fastening screws, DIN 84, min 20mm long

20mm min · confirmed

hex socket screws securing display to mast bracket

14mm · confirmed

Panasonic's official AW-RC400 instruction manual specifies 'Rack-mounting adaptors / Mounting screws M4 x 8 mm' for installing the control panel rack adaptors.

M4x8 mm · confirmed — Panasonic AW-RC400 Operating Instructions

SmallRig's official operating instructions state the SSD Holder mount 'is fixed to the top left corner of the cage by two M4 screws,' with M5 knob screws locking the SSD itself.

M4 (mounting), M5 (knob screws) · confirmed — SmallRig Operating Instruction PDF

The manufacturer's official installation guide instructs users to 'Loosen M4 screws holding lens support clamp' when configuring the lens support rod on the Unified BMPCC4K cage.

M4 (length unspecified) · confirmed — Unified BMPCC4K Cage Installation Guide

Assembly instructions list 'Mounting Screws Qty.4 Screw, M4x8, Pan Head, Cross Recess, Black'

M4x8 mm · confirmed — Elo Touch Solutions UM600683

Mechanical drawing specifies 'VESA MOUNT M4 THREAD, X8, MAX THREAD DEPTH=6MM'

M4 thread, 6 mm max depth · confirmed — Elo Touch Solutions mechanical spec MS-0061836

OEM part listing: 'NCR ATM Parts Repairing Components Screw M4 X 10 M/C Combi 009-0006593'

M4x10 mm · confirmed — NCR OEM part number 009-0006583/009-0006593

OEM listing: 'NCR Self Locking Serrated Nut M4' part 009-0007087, used on NCR ATM chassis

M4 (nut) · confirmed — NCR OEM part 009-0007087

Assembly instructions Bag A: 'SCREW, M4X8, PAN-HEAD, CROSS-RECESS' Qty.10; Bag B: 'SCREW, M4X8, FLAT-HEAD, CROSS-RECESS'

M4x8 mm · confirmed — Elo Touch Solutions QIG600074

Assembly instructions Bag A: 'SCREW, M4X8, PAN-HEAD' Qty.10; Countertop Base 'SCREW, M4X8, FLAT-HEAD, CROSS'

M4x8 mm · confirmed — Elo Touch Solutions QIG600184

Assembly instructions Bag I: 'SCREW, M4X8L, PAN-HEAD, CROSS-RECESS' Qty.8

M4x8 mm · confirmed — Elo Touch Solutions QIG600070