M2.5 x 8mm screws — what they fit & where to buy

Phillips flat-head case assembly screws sold specifically for Pi 5 cases

8mm · confirmed · source

board standoff / distancer mounting screws

5-8mm · reported · source

small bracket and accessory mount points (baseplates are mostly M3)

4-8mm · reported · source

display and controller housing screws

5-10mm · reported · source

captive Torx screws holding the bottom panel on

~8-10mm captive · reported · source

the safety screw locking a plate into a ball head clamp

8-15mm · reported · source

the nosepiece / objective retaining collar on lab microscopes

4-8mm · reported · source

locks the handle nut plate on right-hand conversions

5-8mm · reported · source

holds the glass and housing ring on boat compasses

5-10mm · reported · source

the control board inside the handle

4-8mm · reported · source

collet housing and motor casing

6-10mm · reported · source

the four corner holes used by cases and standoffs

5-11mm standoffs · confirmed · source

display frame and Pi bracket mounting

6-10mm · reported · source

mounting holes on the developer kit board

6-8mm · confirmed · source

Control-surface horn screws

6-8mm · reported

Needle plate and presser foot screws on domestic machines

5-10mm · reported

Pendulum bracket and movement mount screws in European clocks

5-10mm · reported

Torx screws for internal component mounting

5-8mm · reported · source

Driver and board assembly screws

6-10mm · reported · source

Board and lens assembly retention

5-10mm · reported · source

Board and case assembly screws

5-10mm · reported · source

Official HAT spec uses M2.5 brass standoffs, 11mm typical

4-11mm · confirmed · source

CM4 carriers reuse the Pi-standard M2.5 standoff spacing

5-11mm · reported · source

Jetson carrier mechanical specs document M2.5 mounting holes

5-8mm · reported · source

M2.5 standoffs common across the Raspberry Pi ecosystem

5-15mm · confirmed · source

Third-party camera mounts use M2.5/M2 board holes

4-8mm · reported · source

SFF PCs use M2.5 or M3 for internal board and drive mounting

4-8mm · reported · source

M2.5-0.45 x 8mm screw retains the servo horn/arm

8mm · confirmed · source

0.45mm pitch, head 4.32-4.68mm, 2mm hex key

4-20mm · confirmed · source

Head 4.7mm diameter, 1.5mm high

4-20mm · confirmed · source

Button head chassis/link screw, shorter length variant

8mm · confirmed · source

SynthRacks sells M2.5 machine screws used to fix modules to Vector rails or Schroff rails with M2.5 nuts and threaded rails; 8mm length recommended when case uses washers

8mm (also shorter lengths available) · confirmed · source

DIN 915 M2.5x8mm dog-point socket grub screws are a listed stock size used in cine follow-focus set-screw applications (confirmed as a standard grub screw size stocked for this class of gear, not a specific ARRI part page)

M2.5x8mm · reported · source

"Screw M2.5 x 8 Socket Head" listed in GE HealthCare's official service parts store under Maternal Infant Care, manufacturer Datex-Ohmeda

8mm · confirmed · source

Official mounting hole template site states board mounting holes are 2.9mm to accept M2.5 screws/bolts on the standard 85x56mm Pi footprint.

Typically 6-16mm depending on standoff/case · confirmed · source

Winford Engineering DIN-rail mounting plate product page states the plate uses M2.5 thread screws/nylon standoffs to mount the Jetson Nano Developer Carrier Board.

6-10mm standoffs · confirmed · source

M2.5 nominal thread offered in NBK's SSCZS miniature captive-screw line for precision instrument assemblies

4-10mm · confirmed · source

Cartridge Mounting Screw Kit: 'Nominal size (metric): M2.5, Thread pitch: 0.45, Length: 3, 4, 5, 6, 8 and 10 mm'

3-10mm · confirmed · source

'2 x M2.5x3 mm Stainless Steel Screws. 2 x M2.5x6 mm Stainless Steel Screws. 2 x M2.5x8 mm...' cartridge/tonearm mounting fixings

3-8mm · confirmed · source

'The threaded rails or nuts are made to receive either M2.5 or M3 machine screws... You will need M2.5 x 6mm to fix the modules or M2.5 x 8mm if a washer is used'

6-8mm · confirmed · source

Replacement servo horn screw, M2.5-0.45 x 8mm

8mm · confirmed · source

Manual lists M2.5 x 7mm and M2.5 x 9mm black wafer head screws

7-9mm · confirmed · source

M2.5x3 / x6 / x8 countersunk and M2.5x10 / x16 / x18 socket cap in the stock kit

3-18mm · confirmed · source

Dragon hotend variant requires M2.5 x 8mm screws instead of the stock M3

8mm · reported · source

phono cartridge/headshell mounting, pitch 0.45

3-10mm · confirmed · source

turntable headshell cartridge hardware

6/8/10/12/15mm · confirmed · source

M2.5 12mm hex standoffs plus M2.5 10mm screws fastening HAT to Pi

6-12mm · confirmed · source

M2.5 x 4mm solar panel brackets, M2.5 x 6mm sun sensor mount, M2.5 x 8mm secondary structure to X frames

4-8mm · confirmed · source

Chassis screws in M2.5 x 7.0, 9.2, 24.45 and 30.1mm lengths

7-30.1mm · confirmed · source

M2.5 x 8mm screws for the SIM tray access-port cover

8mm · confirmed · source

Product spec explicitly lists 'Screw type: M2.5 non-magnetic hardware' for mounting nearly any phono cartridge to headshell

M2.5x3, M2.5x6, M2.5x8 · confirmed · source

Product titled 'Oyaide M2.5 phono cartridge screw set w/carbon graphite nylon washer', contains 6/8/10mm lengths, explicit M2.5 thread

M2.5x6, M2.5x8, M2.5x10 · confirmed · source

8x M2.5x8mm screws secure the stepper motors

8mm · confirmed · source

M2.5x8mm stainless panel screws and nuts sold for D-series audio rack and server panels

8mm · likely · source

Replacement servo horn screw specified M2.5-0.45 x 8mm, fits HiTec and Futaba servos

8 · confirmed · source

PCB-to-mount standoff screws

5, 8mm · reported · Source: Voron StealthBurner Assembly Manual toolhead PCB section

PCB-to-enclosure standoff stud

5-70mm · confirmed · Source: we-online.com spacer studs page

plastic PCB standoff stud

5-65mm · confirmed · Source: we-online.com spacer studs page

socket head enclosure/board screw (official service parts catalog)

8mm · confirmed · source

chassis feet screws (4x)

8.0mm · confirmed · source

Socket Head Cap Screw (Item No. 6600-0715-403) used in infant monitors and warmers

8 mm · confirmed · source

Screw List: SCREW M2.45D 8.0L K 5.5D 0.8T ZKNL

8mm · confirmed · source

Cartridge-to-headshell mounting screws, M2.5 x 0.45

3-10 mm · confirmed · source